idslogosize2.jpg (6710 bytes)

lucentlogo1.gif (1422 bytes)

Next Generation ISDN Product Family

Lucent Next Generation iPhone Modules and Accessories

iaddonmodulepic.jpg (19783 bytes) The Lucent i2022 and i2023 can accept an optional Add-On Module consisting of 32 Programmable Buttons/Call Appearances.

Depending upon your local Central Office limitations, up to two (2) Add-On Modules may be added. This enables large volume call processing. For larger call handling or Console needs see the Lucent winConsole.

 

 

 
Optional U Interface module

Each i2022 and i2023 will come as standard S/T Interface. An optional U Interface Module can be purchased to enable internal NT1 capability. A local power supply will be supplied with this option.

The items shown to the right are:

Left units - U Interface Black and Misty Cream

Right units - S/T Interface Black and Misty Cream

Note the S/T Interface shows two S ports. One is for normal S/T Line In and the other is a non-powered S/T Interface Out for other devices.

 

 

 iusmodulepic.jpg (26362 bytes)
There is currently one (1) model for optional Data Module available for installation in the Lucent i2022:
Data Module with dual RS232 ports.

Colors: Black or Misty Cream

The Data Module currently supports only TAPI, but will soon support the following:

  • AO/DI
  • BOD/BACP
  • CHAP
  • ML/PPP
  • Stac
  • TAPI
  • Auto Baud
  • V.120
  • Async to 460kbps / Sync to 64kbps
  • D Channel Packet
 idatamod-rs232.jpg (13438 bytes)

Headset Function

Supplying Headset function to the Lucent Next Generation Product Family is accomplished by following the guidelines listed below.

Applicable Next Generation Telephone Models

  • i2021 ISDN Telephone
  • i2022 ISDN Telephone
  • a2011 Single Line Analog Telephone
  • a2011-2 2-Line Analog Telephone

Use Plantronics M12 Vista Amplified Base

Connect via use of Tele-Infonet Headset Adapter cord CC 300316668

Select Headset to attached to M12 Vista Amplified Base

Note: On the i2022 it is possible to use the Lucent Headset CC 300130432 or Earset CC 300294790. However, these items have been discontinued due to fragile contruction and are replaced by the items listed on this document.

Headset choices used with M12 Vista Amplified Base and Headset Adapter Cord

  • H51 or H51N Supra Headset (Monaural)
  • H61 or H61N Supra Headset (Binaural)
  • H91 or H91N Encore Headset (Monaural)
  • H101 or H101N Encore Headset (Binaural)
  • H41 or H41N Monaural Earset

 

Volume Adjustment for the M12 Vista Amplified Base

The M12 Base has two (2) potentiometers for adjustment. the top wheel is for inbound volume and may be adjusted to taste. Outbound volume is adjusted by removing the panel on the left side of the M12, then moving the white potentiometer clockwise for volume increase or counterclockwise for volume decrease. Use the gray tool attached to the bottom of the M12 or a small, slotted screwdriver to make adjustments to the white potentiometer. It is recommended that you make a test call to someone while adjusting the outbound volume so that you verify correct levels.

Note: It is recommended that the volume control on the telephone be lowered once the Headset is activated to avoid "clipping" or poor sound quality due to overdriving the internal amplifier. Use the M12 Vista to control the volume. Be sure to save the setting once you have adjusted the telephone's volume control down.

 

 

 m12top.jpg (21872 bytes)

m12side.jpg (9163 bytes)

Next Generation Menu

Feature Matrix

IDS Home

 
IDS Technologies, Inc.
3714 Alliance Drive, Suite 105
Greensboro, North Carolina 27407 USA
IDS for ISDN Telephones
jakewink.gif (2520 bytes)
This Web Page created and maintained by the techno-folks at IDS Technologies, Inc.
All rights reserved © 1997, 1998, 1999, 2000